Displaying items by tag: Air Conditioning

Multi-Room Wall-mounted INVERTER Heat Pumps

Available in 2-to-1, 3-to-1, 4-to-1 and 8-to-1 indoor units to one outdoor unit systems with wall-mounted and/or ducted indoor unit styles in a wide range of capacities, the MXZ multiroom system has the right solution for your needs.

Multi-zone systems mean that people can enjoy their ideal level of comfort no matter where they are in the home. Each zone (room) operates independently.People in the kitchen, master bedroom or living room can all enjoy the temperatures that makes them feel most comfortable.
If you’re looking for a complete comfort solution for several different rooms, the MXZ multi-zone system is the right choice for you. You can use up to 19different indoor unit combinations so the system is flexible enough to conform to your particular cooling and heating needs with up to four rooms from one outdoor unit. And now with a SEZ ceiling-concealed ducted unit you can enjoy a greater range of zoning options with a MXZ system.

The PKA (Cooling Only)
12000 to 34200 Btu/h Capacity

• INVERTER-driven compressor
• PKA-HAL/KAL use a wirelesshand-held controller
• Ideal for applications such as:- Churches, classrooms, day care rooms,out buildings, guard houses and more

  Test conditions are based on AHRI 210/240.
  Specifications are subject to change without notice.
  Limited warranty: Seven-year warranty on compressor. Five-year warranty on parts.

Ultimate Comfort Meets Ultimate Convenience
Select from a wall-mounted, hard-wired controller(PKA-HA/KA) for ultimate comfort control.
The set-temperature display is large and easy to read.Using the 24-hour timer, you can get the unit operationto start and stop at specified times and to repeat daily.And the convenient remote provides easy control ofthe Fan Speed as well as the col, heat, AUTO andDry modes from anywhere in the room.
The hand-held wireless remote controller is easier touse than most TV remotes for the PKA-HA(L)/KA(L).

Lightweight, Easy-to-install Indoor Unit
The smallest PKA unit measures about 36” wide, 11-1/2” tall and 9-3/4”deep. It weighs just 29 lbs., is easily installed above windows or doorways,and can typically be installed by just two licensed installers in abouthalf of a day. And the PKA-Series models don’t even require ductwork,only a small three-inch opening in the wall or ceiling, so they can be installedin some of the toughest spaces, even on brick and masonry walls.

Auto Vane Control
With a simple press of the OFF button, the vane closes the air outlet for aclean presentation when not in use. During operation, the vane can be adjustedwith the remote controller to the perfect position to direct the airflowhorizontally in cooling mode or towards the floor in heating mode, keepingroom temperature even and comfortable.

MSY/MUY Wall-mounted INVERTER Air Conditioner Systems
 (7)
Single-Room Wall-Mounted Ductless A/C Lineup (Cooling Only)
(9000 to 34600 Btu/h air conditioners)

• Mini-Split, ductless air conditioners
• INVERTER-driven compressor
• Wireless remote controller
• WIDE Vane buttom for a wider angle of air flow, 150° from left to right (on GA24/D30/D36 models)

Ideal for applications such as:

• - Bedrooms, garages and bonus rooms in warm climates
• Limited warranty: Seven-year warranty on compressor. Five-year warranty on parts.
• Standard Wall-mounted System Features:

Easy Installation

• - 3” hole access to connect indoor unit with outdoor unit
• - Indoor unit powered from three wires connected to outdoor unit
• - Discreetly mounted high on a wall for out of sight comfort control
• Catechin and Anti-allergen enzyme filters for high air-purification capabilities
• “Powerful Mode” function permits system to temporarily run at a lower/higher temperaturewith an increased fan speed, which quickly brings the room to the optimum comfort level
• Self-check function with onboard diagnostics
• Advanced microprocessor control
• Auto restart following a power outage
• Wireless remote controller

Single-Room Wall-Mounted A/C Lineup(Cooling Only)
MS Non- INVERTERAir Conditioners
(9500 to 12000 Btu/h)

• Available in cooling only
• Wireless remote controller

Ideal for applications such as

• - Bedrooms, garages and bonus rooms in warm climates
• - Video monitoring room
• Limited warranty: Seven-year warranty on compressor. Five-year warranty on parts.

Standard Wall-mounted System Features:
Easy Installation

• - 3” hole access to connect indoor unit with outdoor unit
• - Indoor unit powered from three wires connected to outdoor unit
• - Discreetly mounted high on a wall for out of sight comfort control
• Catechin and Anti-allergen enzyme filters for high air-purification capabilities
• “Powerful Mode” function permits system to temporarily run at a lower/higher temperaturewith an increased fan speed, which quickly brings the room to the optimum comfort level
• Self-check function with onboard diagnostics
• Advanced microprocessor control
• Auto restart following a power outage
• Wireless remote controller

    Non-Pressurized GT® Flow Center
      THE PRODUCT THAT STARTED IT ALL!
We offer a patented product that has revolutionized the Geothermal world. This single item, the GT FLOW CENTER... made it all possible. From this simple idea arose one of the most remarkable products on the market today. The GT Flow Center is so easy to use that it has been selected for a High School Vocational School teaching program.

The patented GT package contains a water vessel with a self-sealing, removable screw-in top, an air-eliminating dip tube on the inlet, a pump protecting check valve on the outlet, pump(s), and ball valves that allow the pump(s) to be removed for service without loss of fluid to the closed loop system. When fluid is circulated through the canister, air is eliminated through the top of the chamber. When the self-sealing top is in place, the top of the chamber acts as an expansion tank. The top remains open until the system is completely filled and purged. Also note that if you are manifolding inside the GT will purge the system. If you plan to manifold outside, you must use a purge cart to clear lines.

Because the GT Flow Center is completely packaged at the factory, installation is simple. The system can be mounted on the floor or wall. Simply connect a return line from the earth System to the GT Flow Center. Then connect a supply line from the GT to the heat pump unit. That's all there is to adding reliable pump protection to any closed loop system. Also available is the Flowmeter Tool (look in accessories), an exclusive B & D Mfg., Inc. service tool which provides a direct reading of system flow rate, eliminating the uncertainty associated with current methods.

ONE COMPLETE PACKAGE
The non-pressurized GT Flow Center pumping station is unlike other pump protection devices. For instance, the GT Flow Center includes a built-in patented pump protection feature that eliminates the need for a flush cart when filling and flushing a closed-loop system when your manifolds are indoors. And since it is non- pressurized, it allows you to add fluids like anti- freeze or water, while automatically eliminating air from the closed-loop system.

SIMPLE INSTALLATION
As a result of the GT Flow Center being completely packaged at the factory, installation is simple. Just connect the return line from an earth loop to the GT Flow Center, then connect a supply line from the GT to the heat pump unit. Also available is the flow meter tool, an exclusive service tool, which provides a direct reading of system flow rate, and eliminating the uncertainty associated with current methods.

EASY TO OPERATE & MAINTAIN
The system includes a self-sealing feature that keeps dirt & debris out and water in. For you, that means trouble-free operation, easier installation, and fewer call backs. This also means added reliability for the homeowner. In addition, adding anti-freeze is easy, just remove the self-sealing lid and pour it into the air elimination chamber. Since the only moving part of this system are the pump(s), service is minimal. Each part is made to be removed for servicing, without risk of fluid loss or air entry into the system.

A SMART ADDITION TO WATER SOURCE TECHNOLOGY
A homeowner's initial investment in a water source system is slightly more than that of a conventional system. It's an investment that the homeowner will want to protect. Recommending the GT Flow Center will not only add to the reliability of the closed-loop system, it will also add to the customer's satisfaction in the long run.

    Non-Pressurized GT® Flow Center
      THE PRODUCT THAT STARTED IT ALL!
We offer a patented product that has revolutionized the Geothermal world. This single item, the EA FLOW CENTER... made it all possible. From this simple idea arose one of the most remarkable products on the market today.

The patented EA package contains a water vessel with a self-sealing, removable screw-in top, an air-eliminating dip tube on the inlet, a pump protecting check valve on the outlet, pump(s), and ball valves that allow the pump(s) to be removed for service without loss of fluid to the closed loop system. When fluid is circulated through the canister, air is eliminated through the top of the chamber. When the self-sealing top is in place, the top of the chamber acts as an expansion tank. The top remains open until the system is completely filled and purged. Also note that if you are manifolding inside the EA will purge the system. If you plan to manifold outside, you must use a purge cart to clear lines.

Because the EA Flow Center is completely packaged at the factory, installation is simple. The system can be mounted on the floor or wall. Simply connect a return line from the earth System to the EA Flow Center. Then connect a supply line from the EA to the heat pump unit. That's all there is to adding reliable pump protection to any closed loop system. Also available is the Flowmeter Tool (look in accessories), an exclusive B & D Mfg., Inc. service tool which provides a direct reading of system flow rate, eliminating the uncertainty associated with current methods.

ONE COMPLETE PACKAGE
The non-pressurized GT Flow Center pumping station is unlike other pump protection devices. For instance, the GT Flow Center includes a built-in patented pump protection feature that eliminates the need for a flush cart when filling and flushing a closed-loop system when your manifolds are indoors. And since it is non- pressurized, it allows you to add fluids like anti- freeze or water, while automatically eliminating air from the closed-loop system.

SIMPLE INSTALLATION
As a result of the GT Flow Center being completely packaged at the factory, installation is simple. Just connect the return line from an earth loop to the GT Flow Center, then connect a supply line from the GT to the heat pump unit. Also available is the flow meter tool, an exclusive service tool, which provides a direct reading of system flow rate, and eliminating the uncertainty associated with current methods.

EASY TO OPERATE & MAINTAIN
The system includes a self-sealing feature that keeps dirt & debris out and water in. For you, that means trouble-free operation, easier installation, and fewer call backs. This also means added reliability for the homeowner. In addition, adding anti-freeze is easy, just remove the self-sealing lid and pour it into the air elimination chamber. Since the only moving part of this system are the pump(s), service is minimal. Each part is made to be removed for servicing, without risk of fluid loss or air entry into the system.

A SMART ADDITION TO WATER SOURCE TECHNOLOGY
A homeowner's initial investment in a water source system is slightly more than that of a conventional system. It's an investment that the homeowner will want to protect. Recommending the EA Flow Center will not only add to the reliability of the closed-loop system, it will also add to the customer's satisfaction in the long run.

    QT® Flow Center
      The QT Flow Center is designed to provide long, reliable operation in an attractive cabinet, while providing installation and service benefits of the GT Flow Center. The stylish rugged insulated cabinet provides for flexible installation without feeling the need to hide it out of sight. The QT Flow Centers are now standard equipment for geoexchange heating and cooling. The QT Flow Center is one of the greatest things to happen to the geoexchange industry.

ONE COMPLETE PACKAGE
The non-pressurized QT Flow Center pumping station is unlike other pump protection devices. For instance, the QT Flow Center includes a built-in pump protection feature that eliminates the need for a flush cart when filling and flushing a closed-loop system when your manifolds are indoors. And since it is non- pressurized, it allows you to add fluids like anti-freeze or water, while automatically eliminating air from the closed loop system.

SIMPLE INSTALLATION
As a result of the QT Flow Center being completely packaged at the factory, installation is simple. Just connect the return line from an earth loop to the QT Flow Center, then connect a supply line from the QT to the heat pump unit. Also available is the flow meter tool, an exclusive service tool, which provides a direct reading of system flow rate, and eliminating the uncertainty associated with current methods.

EASY TO OPERATE & MAINTAIN
The system includes a self-sealing feature that keeps dirt & debris out and water in. For you, that means trouble-free operation, easier installation, and fewer call backs. This also means added reliability for the homeowner. In addition, adding anti-freeze is easy, just remove the self-sealing lid and pour it into the air elimination chamber. Since the only moving part of this system are the pump(s), service is minimal. Each part is made to be removed for servicing, without risk of fluid loss or air entry into the system.

The QT Flow Center is designed for years of operation!

A SMART ADDITION TO WATER SOURCE TECHNOLOGY
A homeowner's initial investment in a water source system is slightly more than that of a conventional system. It's an investment that the homeowner will want to protect. Recommending the QT Flow Center will not only add to the reliability of the closed-loop system, it will also add to the customer's satisfaction in the long run.

    QT-EA® Flow Center
      SPECIAL 2 CIRCUIT FLOW CENTER NOW AVAILABLE IN QT SERIES!
The QT-EA Flow Center is designed to provide long, reliable operation in an attractive cabinet, while providing installation and service benefits of the EA KFC. The stylish insulated cabinet provides flexible installation without feeling the need to hide it out of sight.

SIMPLE INSTALLATION
Because the QT-EA Flow Center is completely packaged at the factory, installation is simple. The system should be mounted on the floor. Simply connect a return line from the earth system to the QT-EA Flow Center. Then connect a supply line from the QT-EA to the heat pump unit. That's all there is to adding reliable pump protection to any closed-loop system. Also available is the Flowmeter Tool, an exclusive service tool which provides a direct reading of system flow rate, eliminating the uncertainty associated with current methods.

    HSS® Series
      A NON-PRESSURIZED STAINLESS STEEL BUFFER TANK FOR HYDRONIC HEAT!

•     Available Sizes: HSS-12, HSS-20, HSS-30, HSS-40, HSS-60, HSS-80
•     1 1/4", 1 1/2" or 2" inlet & 3/4" or 1" ball valve outlets
•     Water temperature not to exceed 150 degree max
•     Designed for 6 to 10 gallons per ton of buffer volume
•     115V pump on Hydronic Heat side
•     230V pump with Water side
•     Hydronic pump relay standard sensor for One Stage Heat, Two Stage Heat or Heating & Cooling built in
•     Pump selection based on flow and foot of head per circuit
•     Water side only 3 heat pump circuit max
•     Hydronic 26/99-3 is a three speed pump (low-med-hi)

The Greensource CDi Series SM Model geothermal heat pump comes equipped with Bosch’s commitment to Creative Design and Innovation (CDi for short). The SM Model is our most efficient unit and provides the quality that only Bosch can provide including:

• Up to 37.0 EER (part load) and up to 28.0 EER (full load) GWHP
• Up to 5.2 COP (part load) and up to 5.1 COP (full load) GWHP
• 10 year Parts Limited Warranty
• 10 year Labor Limited Warranty
• White pre-painted sheet metal cabinets
• Two capacity operation with scroll compressor technology
• Constant speed CFM variable speed ECM
• Fiber-free, closed-cell insulation helps to keep the system high efficienct improving your indoor air quality.
• Whisper quiet operation with sound level as low as 52 dB
• Patent-pending floating base pan
• Evaporator coil with tin plated hair pins and aluminum fins for durability and reliability
• LCD display
• Low and high pressure switch protection
• Freeze protection for both evaporator coil and water condenser coil
• Condensate overflow switch protection
• Anti-short cycling
• Brownout/low voltage protection
• Designed with you in mind: fully customizable to meet your individual installation needs with multi-positional configurations
• Combine the Greensource CDi Series SM Model geothermal heat pump with a Bosch innovative thermostat designed to work exclusively with your system
• Stainless steel drainpan
• 2" MERV-11 filter

Optional Features

• Cupronickel coaxial heat exchanger
• Internal electric heat
• Dehumidification options
• Comfort alert diagnostic module
• SmartStart
• Communicating thermostat accessory
• Domestic water heating
• IAQ product accessories